Home - Return to Previous Page
Additional Images

AVO FRS/BRZ Turbo Kit STAGE 1 : S6Z12GS7A003T

AVO 13+ Subaru BRZ / 13+ Scion FR-S Bolt On Turbo Kit w/ FMIC & Ceramic Coating Stage 1 S6Z12GS7A003T

avoS6Z12GS7A003T
AVO's front-mounted Stage 1 turbocharger kit for the Subaru BRZ and Scion FR-S is finally here, with a North American shipping date of late June 2013! The kit is designed to work with both RHD and LHD models in all countries, and extensive testing has been done on both the Japanese Subaru BRZ and the US Market Scion FR-S. The Japanese BRZ has been track tested from day 1, and the US Market FR-S just spent two days and 1400 miles testing and tuning in varying conditions, from 6000 feet and 0 degree temperatures, to sea level and below in the desert! This was done to ensure our kit will hold up as a daily driver where ever you go, whatever the conditions. All testing in the American market was conducted on 91 and 92 octane pump gas to ensure this is going to handle daily driving as well as the track.

The turbocharger kit is designed from top to bottom specifically to the FR-S and BRZ, and consists of the all the parts necessary to bolt the kit up to the car. We utilize an AVO18/49 turbocharger that mounts up under the front of the engine via our stainless steel unequal exhaust manifold, and then it bolts up to the stock exhaust with our polished stainless steel turbo outlet (also referred to as a downpipe). Cooling the pressurized air is an aluminum bar and plate front mount intercooler which uses black piping throughout, mechanical oil scavenging pump, oil reservoir tank, and all necessary water and oil hoses and fittings. Tuning is by AVO Turboworld via EcuTek reflash tools, and we will provide an AVO Stage 1 base map free of charge with the Stage 1 kit.

This turbo kit has been designed to bolt up to the stock air intake box and to the stock exhaust system. We have spent a lot of time ensuring it will work with the standard fueling system for a complete bolt on and go setup. The beauty of the system is that it looks very stock from above! The FMIC has been specifically designed to fit with the standard bumper without trimming as well, and on FR-S models would be be difficult to see unless you are looking for it.

So what can you expect from this kit? From our testing, you will see anywhere from 220 to 250whp on pump gas, dependent entirely upon the quality of the pump gas. This is due entirely to the fact that the stock motor is 12.5:1 compression, incredibly high for a n/a motor. This makes gas quality even more important than ever! If it wasn't for the fact that this FA20 motor is a completely different and modern design with an incredibly well made combustion chamber, we wouldn't even attempt to turbocharge these cars. But while many people associate it with the old EJ20 series motors from Subaru, there is absolutely no comparison besides the fact they are both boxer 4's made by Subaru. The entire design of the engine is different, especially the combustion chamber, which has been improved tremendously from anything previously made by Subaru.

Not only is the engine a major step up, the ECU on this car is also a great design, reacting incredibly fast to knock and adjusting parameters to compensate. This helps increase the reliability of the turbocharged motor. As is well known by now, this is also a direct injection motor, helping both power and gas mileage. We've seen mpg figures as good as stock on the freeway, probably better than stock as we were not exactly sitting on cruise control during our testing!

As you can see from the dyno chart, we saw 230whp (276 crank hp) and 197 ft/lbs of torque at 5-6 psi on 92 octane gas literally from a nearby Chevron gas station. This was with the stock airbox with an AVO high-flow panel filter installed, and a stock secondary cat in place. All these figures were reached on the stock fueling system as well!

See Documents below for Install Instructions

NOTE: The kit does NOT include the EcuTek license which must be purchased separately. If you or the end user already has an EcuTek you can get the tune from AVO Turboworld USA at 206- 546-4455 or via email at paul@avoturboworld.com.

OR You may purchase one here : http://scionpro.com/i-13474993-avo-turboworld-ecutek-pro-frs-brz-2013-s6z12ee9a001t.html

Turbo Specifications: AVO18/49 Turbocharger with 5-7psi actuator - compressor wheel size 49.2/56 | exhaust wheel size 50.5/68 This specially designed AVO18/49 turbocharger comes with a 5-7 psi actuator for precise boost control at lower psi levels, ensuring engine longevity. The turbocharger is rated for 380hp of flow, so there is certainly headroom available with it from the base stage 1 kit, which is doing 276hp on 92 octane.

Mechanical Oil Pump Specifications: We are unique in utilizing a mechanical oil pump that we locate at the back of the engine, which runs off the back of the RH camshaft. There is also a oil reservoir tank right off the turbocharger itself. This is the most reliable way to pull oil through the turbo to the engine, as it keeps the flow rate tied to the rpm speed of the motor, ensuring that it's properly scavenged at low rpms and idling, and has enough at high rpms.

Front Mount Intercooler Specifications: Bar & Plate Aluminum Intercooler with cast end tanks. Length = 19" Height = 8" Width = 3" The intercooler kit utilizes black wire-reinforced silicone piping and two black powder coated steel piping. The intake piping has ports to mount up a variety of blow-off valves, even OEM ones for a full stealth look.

Automatic Version Specific: The Automatic version of the BRZ, FR-S, and GT86 has some additional hardware for proper fitment.

Blow-off Valve: A blow-off valve is strongly recommended to be fitted to ensure a stable idle. We have two different types of blow-off valves available, an OEM-style BOV and an Adjustable BOV that can be set up for vent to atmosphere.

Kit includes the EcuTek base tune. An EcuTek License and OBD-II cable are optional. Ceramic coating on the Exhaust Manifold, Turbocharger, and Turbocharger discharge pipe are now standard.

Additional OPTIONAL BUT SUGGESTED ITEMS:

Breather Tank System: We strongly suggest one of our two Breather Tank Kits to be fitted along with the turbo kit for maximum reliability against oil blow-by. There are two versions, a street and a track kit. The track kit comes with additional hardware for dealing with the extremes of circuit racing. Both kits come with all fittings and accessories necessary, including a turbo-specific high pressure PCV valve replacement that will deal with any potential boost leaks and protect against pressurizing the crankcase under boost. This is also a requirement for higher boost builds.

Availability: CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Shipping: International Shipping is available. For quote email STEVE@D2BDMOTORWERKS.COM with your full name, house number, street name, city, province, country, and postal code. Free Shipping in 48 continuous states only.
Was: $4,450.00
Sale: $4,395.00
Save: 1%
Save: $55.00

Customize Your Item

- Select -
 * required
Qty:
Free Shipping!

Description



Details

Shipping Information

  • Item Requires Shipping
  • Free Shipping!
  • International Shipping is available. For quote email STEVE@D2BDMOTORWERKS.COM with your full name, house number, street name, city, province, country, and postal code. Free Shipping in 48 continuous states only.

Customer Reviews

Comment Total Reviews (0)

Write the First Review!

You must login to post a review.



  • D2BD Motorwerks
  • We're your Styling, Air Ride and Mild Performance Headquarters
  • Extensive SelectionCovering your Air Suspension, Styling, and Mild Performance Needs.
  • Low Prices EverydaySee it for less? Let us know! Request a price match.
  • Fast Shipping See our detailed shipping rates. Easy Returns. View our policies and procedures.
  • Superior Customer ServiceFind the answers to commonly asked questions.
  • Secure Web TransactionsAll transactions involving personal information are secured through SSL encryption.
    WSM SSL COMODO

Share AVO FRS/BRZ Turbo Kit STAGE 1 : S6Z12GS7A003T on Facebook